Latest from Material Handling

BvL Oberflächentechnik
0 1021 Forg Bv L Niagara 800
OTEC Präzisionsfinish GmbH
Otec Stream Finishing Machine 800
Dillon Manufacturing
Np Dillon Fast Trac Jaw Nuts1 800
Verti-Lift
Verti Lift Double Wide Lifts 800
Monaghan Tooling Group
Mtg Id Burnishing Grouped 1540

Achieving Traceability on Piston Forgings

July 30, 2012
Bharat Forge America Inc. makes good use of a special dot-peen marking machine designed to operate on-the-factory-floor. to impart critical production-history data to each finished component.

When Bharat Forge America Inc., a producer of closed-die hot forgings, was contracted by a leading piston manufacturer to provide large piston forgings for a new offhighway equipment engine, it was required to del iver each forging marked with information about its production history.

The metallurgical integrity and consistency of the forging is paramount, so the marking method preferred by the manufacturer was dotpeen. The dot-peen marking method imposes no perceivable stresses on the forgings, and does not create any possible arcing situations, which could occur with a laser marker.

John Turner, the piston program manager for Bharat Forge, says, “The forging processing cell that we designed for the pistons required that the marking be performed on the factory floor in the inspection area located near the hot-forging presses.”

“With that as a requirement, we knew that we would need to talk to a marking company that designs and builds special marking machines that are rugged, can handle the harsh environment, and provide the programmable dot-peen technology that we needed. We also needed a marking company that could ‘turnkey’ the whole marking process — not just provide us a marking unit. Columbia Marking Tools turned out to be that company, and provided us with a good turnkey dot-peen marking solution.”

Turner explains: “The information that we are required to place on the pistons includes a heat-lot identification number, the die set that was used, a part number, a Bharat supplier identification, and the customer’s logo. That’s quite a bit of information that needed to be placed in an area on the piston that ultimately would not be machined off.”

He continues, “That ideal marking area was determined to be the two areas on the opposite sides of the wrist pin bore location on the piston. As a result, the total marking area became fairly large, which required a dot-peen marking machine with a large marking window, and the ability to mark up to seventeen 0.25-inch characters.

“Columbia Marking Tools has a compact PM Micro AXL dot-peen marking unit that has a 200-mm (7.87-in.) 80-mm (3.15-in.) marking window that met our requirements. We are using the extended carbide pin design with a protective debris shield that adequately protects the stepper motors and ball-screw drive of the marking head.”

Turner adds, “Having the marking capability was just part of what we needed in a machine design. Columbia designed a stand-alone machine that had a rugged machine base and table to which was mounted a manual load/unload rotating two-part piston-locating fixture. The PM Micro marking unit is mounted to the back of the machine base and the parts are presented to it for marking. A part-present sensor mounted above the fixture is provided to detect when a piston is in position for marking.”

The PM Micro CNC-controller is contained in an enclosure that is attached to the machine base and located at eye-level. The enclosure also includes a keyboard for programming. The standard unit interfaces with existing Windows XP or Vista systems using Columbia’s Signumeric software, which allows Bharat Forge to create the logos and special graphics required.

Data entered by an operator via the keyboard can be viewed and edited on an LCD display before any marking is performed. The text can be fixed or variable, numbering can be sequential, and date coding can be set up to be automatic, and character size can vary in 0.1-mm steps.

The unit is flexible, too, because the penetration depth is easily adjustable through a pressure regulator. “Although some of the pistons that we are marking have different metallurgical make-up,” Turner points out, “their hardness is the same, so the penetration set-up for the parts is also the same.”

The Columbia PM Micro dot-peen unit is fast and versatile. Because of its small size, 5.5 7 7 in., it is easy to integrate into a production system. The movement for the marking head is provided by high-torque stepper motors and ball-screw drive that produces the fast 300-mm-per- sec speed, which can mark up to eight characters per second. The electric motors for the X-Y axis require 110 VAC power; 30-75 psi is the operating range for the air-powered pneumatic dot-peen action.

With on-board I/O and serial interface, the unit can receive information two different ways, regardless of the type of PLC. It can be designed for automatic, semi-automatic, or manual operation.

Turner explains further about the project, “As the production schedules for the piston program have expanded we have found the need to increase the speed of the marking process as well. The Columbia equipment can easily handle our increased production requirements; it’s the manual loading and unloading of the parts that is limiting the production cycle time,” according to Turner.

“As a result, we are in the process of building a new manufacturing cell that will utilize three robots, which will present the parts to the marking station. Because of the modular design of the Columbia marking machine, it will be easy to reposition the PM Micro unit and the control panel in the new manufacturing cell design. Application engineers from Columbia Marking Tools will be assisting us in finalizing the details of that design.”