The AZM 200 Series is designed for machine/work cells where access to a hazardous work area must be controlled until safe conditions exist. Their solenoid-latching feature permits locking a machine guard until dangerous conditions, which may exist immediately after removal of power, have abated. Solenoid-latching may be controlled by a time delay, motion detector, position sensor or other suitable component....

The ZS71 with optional E-Stop is designed to provide continuous emergency stop along exposed areas of machinery and conveyors which present hazards to operators/maintenance personnel. The unit features a positive-opening NC contact which is forced open when the trip-wire is pulled. This design also assures actuation if the operator falls into, leans on, or is pushed against the trip-wire. In addition, the switch is designed to operate if the trip wire is cut or goes slack....

The AZM161 Series is designed for machines/work cells where access to a hazardous work area must be controlled until safe conditions exist. Their solenoid-latching feature permits locking a machine guard until dangerous conditions, which may exist immediately after removal of power, have abated. Solenoid-latching may be controlled by a time delay, motion detector, position sensor or other suitable component. Restart until the guard is closed and the solenoid-latching pin is in the locked positio...

The Series AZ15/16 is designed for use with movable machine guards/access gates which must be closed for operator safety. Their positive-opening NC contacts provide a significantly higher level of safety than conventional spring-driven switches…and their tamper-resistant design prevents bypassing with simple tools, bent wires or other readily available means. Their IP67 rating makes them ideal for interlocking safety guards in hostile environments....

The CSS 180 non-contact, electronic safety sensor is designed for application in safety circuits and is used for monitoring the position of movable safety guards. In this application the safety sensor monitors the closed position of hinged, sliding or removable guards with the aid of a coded actuator. The CSS 180 Safety Sensor fulfills the requirements for proximity devices with defined behavior under fault conditions according to EN 60947-5-3 with the classification PDF-M (self-monitoring)....

The Series BNS33 coded-magnet sensors are designed for use as a safety interlock switch on movable machine guards/articulating robot arms. Each tamper-resistant sensor set consists of a multiple reed switch unit and a coded-magnet actuator. The reed switches, wired in series, will only close in the presence of their matched magnetic field array. Both switch and magnet assemblies are sealed to IP67 (submersible) standards. Their tamper-resistant design prevents bypassing with a simple magnet or i...

SCHMERSAL's Series SLC/SLG safety light curtains feature a built-in alignment aid, operation and diagnostic displays, and an integral safety controller with two PNP (500mA) safety outputs. Each is UL and CSA-certified and satisfies all relevant directives to bear the CE mark for use in Safety Category 4 systems. ...

The 3 contact TESZ Series are designed for use with hinged movable machine guards. Their tamper-resistant design and positive-opening NC contacts provide a significantly higher level of safety than conventional, spring-driven limit switches. Their compact, low-profile design and IP65 rating make them ideal for interlocking hinged safety guards in industrial environments....

Safety controllers are designed to increase the level of safety in machine guarding and/or E-stop control circuits. They feature redundant, dual channel, cross monitoring logic circuits. These continuously check for, and detect, faults in the system's safety circuit components and interconnection wiring. They are available in both conventional electro-mechanical relay based and unique microprocessor based models....

Schmersal is pleased to announce the release of their fully-integrated, multi-functional safety light curtains and grids. This next generation of optical safety sensors meet all North American approvals, including cULus, as well as European Norms EN/IEC...

Schmersal is pleased to announce the extension of their family of BNS non-contact safety sensors. The BNS40S coded magnetic sensor meets stringent North American and European approvals, is CE and cULus approved, and can be used in the highest level of m...

Schmersal is pleased to announce the extension of their family of non-contact electronic safety sensors. The RSS36 sensors meet stringent North American and European approvals, are CE and cUL approved, and can be used in the highest level of machine saf...